我可憐的魚兒

再我魚缸裡的照顧下

都沒有好下場

於是我再次祭出法寶

將!!!將!!!將!!!tds筆登場

(內附TDS筆、收納盒、說明書(英)、含電池)

DSCN5158.JPG

 

使用的是CR2032水銀電池

位於TDS筆的尾部

蓋子有方便放於口袋的設計

DSCN5161.JPG

 

筆頭的探測頭(因該是這麼稱呼吧~噗)

 ↓

DSCN5160.JPG


藍色為開關

可以顯示三位數

單位為ppm(百萬分之一) 

DSCN5163.JPG

小試身手

先來測測自來水

自來水:63ppm

DSCN5166.JPG

三胞胎出來的水

(想了解三胞胎請點我)

三胞胎:61ppm


 DSCN5170.JPG  

沒有魚但很多懸浮物的魚缸

測得:95

DSCN5167.JPG    

 

 

------------補記------------

非常髒的魚缸更換三胞胎的水後

測得得數據為:84

忘記拍照片請見諒

 

 

複習一下

自來水:63ppm

三胞胎:61ppm

(換水前)魚缸:95ppm

(換水後)魚缸:85ppm

得到個幾個心得

1.三胞胎使用後只有降低2ppm的效果,讓我有點失望

2.魚缸換水前後差異到10ppm效果顯著,證明換水真的有效(笑??!!)

 

另外我特別去測試一下生態缸

測得的值為14ppm

不是我眼白多

就是TDS筆壞了

不過話說也因如此他們才活的

那麼愉快.....

 

我對TDS並未有很深入的了解

理論上TDS的值是越低越好(純水TDS:0ppm)

但是TDS值與其他數值息息相關

將來有機會再繼續分享TDS與其它吧!!!

 

 

以下是自行翻譯的說明書供參考

=========================原文======================P.1

Applications

water purification

reverse osmosis

distillation

de-lonization

pool & spa maintenance

aquariums

plating lndustry

cooling towers & Boilers

Photographic labs

=========================翻譯======================P.1

應用

.淨化水(這我真的不知道是什麼)

.逆滲透水

.蒸餾水

.電解水

.游泳池與溫泉

.水族館

.電鍍業(可以跟我說電鍍為什麼需要嗎?)

.冷卻塔與鍋爐

.攝影實驗室(????)

========================原文=======================P.2

Calibration

Use 130 ppm (NaCI) standard solution for calibrating

To calibrate:

1.remove the top cap from the probe

2.dip the pm-3000 into the calibrating solution and obtain a reading as described in the operation section.

3.insert small screwdriver into the calibration hole and adjust the display to read 130

4.rinse with distilled water and dry

========================翻譯=======================P.2

校準

使用130 PPMNaCl)標準溶液的較準
要校準:

1.從頭端將比筆蓋卸下

2.依操作將PM-3000沾入標準溶液並讀取其值

3.將小隻的螺絲起子插入校準孔調整顯示至130

4.用蒸餾水洗淨保持乾燥

========================原文=======================P.3

INSTALL/CHANG BATTERY

Remove the battery compartment cover

install a new CR2032 battery ,and make sure the battery is properly placed with “+” side out.

close the battery compartment. Then press the button to check if LCD illuminates .if the LCD does not illuminates, check if battery is good or is properly installed , and then repeat the above steps.

change battery when the LCD becomes dim 

========================翻譯=======================P.3

安裝/更換電池

.取下電池蓋

.安裝一個新的新的CR2032電池,並確保正確放置於電池端”+”的位置

.關閉電池蓋。然後按下按鈕,以檢查螢幕是否有點量,如果顯示器沒點亮,請檢查電池是否安裝好,然後重複剛上述步驟。

.當顯示器變暗時,更換電池。

========================原文=======================P.4

Specifications

Auto-offYES

AutomaticYES

Temperature

Compensation

TDS Range1-2,999ppm

Resolution1ppm

Accuracy+/-5% at 25 (≦2000ppm)

Conversion

BatterySingle 3V  Lithium CR2032

Weight1.3 oz 37g

Battery life30hrs

Size(LxWxH)5.8x1.2x0.6 in  146x30x15 mm

========================翻譯=======================P.4

規格

自動關機:有

自動偵測:有

溫度補償

TDS範圍:1~2(最小),999(最大)        

辨識率:1ppm(這個不太懂)

精確度:在25度環境下正負5%(≦2000ppm)

轉換(??)

電池:13V CR2030水銀電池

重量:37/1.3盎司

尺吋(xx)5.8x1.2x0.6英吋 / 146x30x15公厘

========================原文=======================P.5

Operation procedure

Remove the probe cap, and press the button . the LCD will display “000”

Dip the PM-3000 into the sample.

Stir gently to remove any air bubbles , and then wait for the reading to stabilize . Remove the meter from water to obtain TDS reading. The meter has an auto reading hold function to keep reading on LCD until next measurement or power is off.

During stabilization the TDS movement should be minimal.

For a new measurement , press button to clear reading . the LCD will display ”000”

After measuring, gently shake the meter 2-3 times to remove any residual water from the probe before putting the cap on. The meter automatically shuts off after approximately 15 seconds from power-on

Always rinse with distilled water and dry after each test.

To turn off the meter manually ,press the button for approximately 3 seconds

Replace probe cap

========================翻譯=======================P.5

操作步驟

.取下探頭保護蓋,然後按下按鈕。顯示器將會顯示”000”

.將PM-3000浸入樣品中

.輕輕攪拌,以消除任何氣泡,然後等待數值穩定。儀表移開水面後讀取TDS值,該儀器具有自動保持數值的功能,以保持顯示器上得取數值,直到下一次測量或電源關閉。

.在穩定的TDS中變化量因該不大。

.將測試新的樣本時,按下按鈕,顯示器將會清楚顯示”000

.測量結束後,輕輕搖動儀器2~3次,以去除探測頭上多餘的水,儀器在15秒後便會自動關閉。

.必須用蒸餾水清洗,乾燥後才可以下次測試。

.若要關閉儀器,長按按鈕3秒即可。

.蓋回探頭保護蓋

========================相關圖片=======================

sshot-3.jpg

========================相關圖片=======================

sshot-2.jpg

依位置翻譯

電池蓋

校正選鈕 , 電池更換處

(正面)

探頭保護蓋

(背面)

 

========================相關圖片=======================

sshot-1.jpg
單鍵操作 (15秒後自動關閉)

大螢幕顯示器

浸入水平

arrow
arrow

    吉米飯 發表在 痞客邦 留言(2) 人氣()